Looking for Answers about Delta Replacement Parts?

Customer questions and answers for
Delta Replacement Parts

Replacement Parts
Customer questions and answers:
92 Questions
 | 
102 Answers

Customer questions and answers for Delta Replacement Parts

Question

Looking for a shower cartridge for a home build in 1999 1400 series shower only

Age: 55 to 64
Gender: Male
Project Type: Replacement
Ownership: 10+ years
Skill Level: Intermediate
Topics: Care/Maintenance
asked 6 days ago
Customer avatar
by
Browncv
Chesterfield, VA, USA
on Replacement Parts
0points
0out of 0found this question helpful.
Answer this question
1 answer
Answers
answer 1
Hi Browncv,

Thank you for your question. The age of your 1400 series should take Delta Faucet model RP19804 cartridge.

Thanks.

Jody
Skill Level: Advanced
answered 5 days ago
Customer avatar
by
Delta1
0points
0out of 0found this answer helpful.
Question

Can you replace this fixture without redoing the plumbing?

Age: 55 to 64
Gender: Male
Project Type: Replacement
Skill Level: Beginner
Topics: Assembly
User submitted photo
asked 1 week, 6 days ago
Customer avatar
by
Willie Nelson
#3, Columbia, TN 38401, USA
on Replacement Parts
0points
0out of 0found this question helpful.
Answer this question
1 answer
Answers
answer 1
Hi Willie Nelson, Thank you for your question. As a general rule of thumb if the set screw is on the back of your existing roman tub spout the newer trims should work. If the set screw is on the front of the spout, or if there is no set screw at all on the spout the rough in valve will have to be changed as well. Check that the spout connection on the existing valve matches the connection on the new rough in R2707. Here is the link.
http://www.deltafaucet.com/bath/det...
Thanks,
Dave
Skill Level: Advanced
answered 1 week, 6 days ago
Customer avatar
by
DeltaFaucet2
0points
0out of 0found this answer helpful.
Question

tub is leaking behing the diverter and tub spout

Do these parts need to be replaced due to age. delta number RP17453 I think?
Age: 55 to 64
Gender: Male
Project Type: Replacement
Ownership: 10+ years
Skill Level: Intermediate
Topics: Care/Maintenance
asked 2 weeks ago
Customer avatar
by
ter
Smithfield, VA, USA
on Replacement Parts
0points
0out of 0found this question helpful.
Answer this question
1 answer
Answers
answer 1
Hi Ter, Thank you for your question. You can try soaking the tub spout in a 50/50 solution of vinegar and water to help break up mineral deposits which is the most likely cause of the leaks since the mineral build up doesn't allow the diverter to seal properly. If the cleaning does not improve the performance of the tub spout, the spout should be replaced.
Thanks,
Dave
Skill Level: Advanced
answered 1 week, 6 days ago
Customer avatar
by
DeltaFaucet2
0points
0out of 0found this answer helpful.
Question

Changing roman tub trim

I am changing the roman tub trim out for a customer. The house was built in 1991 so it has the old style rough valve. Will the new roman tub trim fit the old style rough valve?
Age: 45 to 54
Gender: Male
Project Type: Replacement
Ownership: 10+ years
Skill Level: Advanced
asked 2 weeks, 1 day ago
Customer avatar
by
Ed
Raleigh, NC
on Replacement Parts
0points
0out of 0found this question helpful.
Answer this question
1 answer
Answers
answer 1
Hi Ed, Thank you for your question. As a general rule of thumb if the set screw is on the back of the tub spout the newer trims should work. If the set screw is on the front of the spout, or if there is no set screw at all on the spout the rough will have to be changed. Check that the spout connection on the existing valve matches the connection on the new rough in R2707. Here is the link.
http://www.deltafaucet.com/bath/det...
Thanks,
Dave
Skill Level: Advanced
answered 2 weeks ago
Customer avatar
by
DeltaFaucet2
0points
0out of 0found this answer helpful.
Question

I am looking to replace our existing gold Roman Tub faucet and handles using our existing piping with a brushed nickel faucet and handles.

Please advise which replacement unit will work and if I can purchase it locally or will I order on-line.
Gender: Female
Project Type: Replacement
Ownership: 10+ years
Skill Level: Intermediate
User submitted photo
asked 2 weeks, 4 days ago
Customer avatar
by
JoAnn
Maple Valley, WA
on Replacement Parts
0points
0out of 0found this question helpful.
Answer this question
1 answer
Answers
answer 1
Hi JoAnn, Thank you for your question. Based on your picture our new roman tub trims will not work with your existing rough in valves. The entire faucet trim and rough would have to be replaced.
Thanks,
Dave
Skill Level: Advanced
answered 2 weeks, 1 day ago
Customer avatar
by
DeltaFaucet2
0points
0out of 0found this answer helpful.
Question

comparison of faucets from different stores

I am planning to buy a new Delta kitchen faucet. The plumbing supply store representative told me that their Delta faucets would be a higher quality than those sold at Lowes or Home Depot. The difference would be that some parts inside the faucet would be plastic rather than metal, etc.

Is there any difference in the quality or parts between your faucets according to which store or online dealer sells them?

Thank you for the information
Topics: Purchase
asked 2 weeks, 6 days ago
Customer avatar
by
Patti
on Replacement Parts
0points
0out of 0found this question helpful.
Answer this question
1 answer
Answers
answer 1
Hi Patti, Thank you for your question. If you are purchasing a Delta product whether online, from a retailer, or a plumbing supply if the product is the same model number the product will be exactly the same. The faucet model 567LF-MPU purchased from Amazon, Home Depot, or Fergusons would be the exact same item.
Thanks,
Dave
Skill Level: Advanced
answered 2 weeks, 6 days ago
Customer avatar
by
DeltaFaucet2
0points
0out of 0found this answer helpful.
Question

faucet wont give enough water pressure, It comes out trickling. What can I do?

Once in a while after turning it on/off it will come on full pressure. I changed the batteries Do not know the Model, just bought the home in December.
asked 4 weeks, 1 day ago
Customer avatar
by
Sam
Baton Rouge, LA, USA
on Replacement Parts
0points
0out of 0found this question helpful.
Answer this question
1 answer
Answers
answer 1
Hi Sam, We are sorry that you are experiencing a problem with your faucet. You will need to determine where the water flow is being obstructed. I have attached the part of the manual that covers low flow below. If cleaning the aerator and debris screen do not improve the flow you will want to check the water stops and check valves, the wand assembly, and the solenoid itself to see what the water flow is like at those locations. This should help isolate the cause and once cleaned or replaced improve the faucet performance.
Thanks,
Dave
Skill Level: Advanced
User submitted photo
answered 4 weeks ago
Customer avatar
by
DeltaFaucet2
0points
0out of 0found this answer helpful.
Question

Replacement of old roman tub spout

I'd like to replace the trim on a 1995 Delta roman tub spout, anti-swivel hole in tub, and set screw on back so I bought the BT2710 trim kit and it does not clear the side of the tub (too short a reach). Is there any other longer trim that would fit this?
I've read your answers to similar questions and you mention a BNT2710SS model, but I can't find that anywhere to check it out, what is a BNT vs BT?
Age: 55 to 64
Gender: Female
Project Type: Replacement
Ownership: 10+ years
Skill Level: Intermediate
Topics: Features
asked 1 month, 2 weeks ago
Customer avatar
by
Kathi
on Replacement Parts
0points
0out of 0found this question helpful.
Answer this question
1 answer
Answers
answer 1
Hi Kathi, Thank you for your question. The roman tub trim that has the largest base to cover the anti-swivel pin hole is the T2710. The spout for this trim is 1-11/16" longer than the spout in the model BT2710. The BNT2710SS is not a valid model number, it is most likely a typing error.
Thanks,
Dave
Skill Level: Advanced
answered 1 month, 2 weeks ago
Customer avatar
by
DeltaFaucet2
0points
0out of 0found this answer helpful.
Question

Tub Spout Replacement

I am replacing my basic builder grade Monitor 13 series trim with Lahara trim. The problem I have run into is that the current tub spout is a front threaded spout and the Lahara tub spout is a rear threaded. What are my options to be able to use the Lahara spouts?
Age: 45 to 54
Gender: Female
Topics: replacement
asked 2 months ago
Customer avatar
by
Michelle
Arizona, USA
on Replacement Parts
0points
0out of 0found this question helpful.
Answer this question
1 answer
Answers
answer 1
Hi Michelle, Thank you for your question. The RP51303 tub spout that ships with the Lahara 13 series will ship with an adapter that will thread onto 1/2" pipe or sweat onto 1/2" copper pipe. If your existing spout uses galvanized pipe you will have to purchase a shorter pipe nipple. If your existing spout is using copper pipe you will in most cases cut the pipe to a shorter length and sweat on the adapter to make the new spout fit properly. The spout instructions will cover the necessary installation specifications.
Thanks,
Dave
Skill Level: Advanced
answered 2 months ago
Customer avatar
by
DeltaFaucet2
0points
0out of 0found this answer helpful.
Question

What trim will fit R2700 stem?

I have a circa 1993 Delta Roman tub faucet, gold in color that I would like to upgrade to a more modern fixture. The existing stem has a plastic adapter that is slid over the stem to accept the handle. I am told this is R2700 series, although I cannot find any numbers on the stem. The spout has a anti rotation pin that enters a hole drilled in tub. I would also know how to remove the gold collar plate that sits flush with the tub surface under the faucet handle. I would like to know what series of trim are compatible with the stem series installed. Thanks
Age: 55 to 64
Gender: Male
Project Type: Replacement
Ownership: 10+ years
Skill Level: Intermediate
Topics: Assembly
User submitted photo
User submitted photo
User submitted photo
User submitted photo
User submitted photo
asked 2 months ago
Customer avatar
by
Jim
Leonardtown, MD 20650, USA
on Replacement Parts
0points
0out of 0found this question helpful.
Answer this question
1 answer
Answers
answer 1
Hi Jim, Thank you for your question. With the swivel pin installed the Delta trim that comes close to covering up the additonal hole under your existing faucet is the BT2710 or BNT2710SS. The remainder of the trim is compatible with your existing rough.
Thanks,
Dave
Skill Level: Advanced
answered 2 months ago
Customer avatar
by
DeltaFaucet2
0points
0out of 0found this answer helpful.
Question

Looking to change from a brass bathroom to a stainless steel bathroom

Our house is 20 years old. Looks like we have the 13 series but may be a model earlier. Closest I can see is the model T13220-PBSHC but we have the standard round plastic handle.
There is no cartridge. There is a brass retaining screw or disc that holds in the round sphere that has three holes on the top and three holes on the bottom

We would prefer to just upgrade to stainless steel without having to cut into the Sheetrock and install a new rough in.

Thanks for your help.
Age: 55 to 64
Gender: Male
Ownership: 10+ years
Skill Level: Advanced
Topics: upgrade
asked 2 months, 3 weeks ago
Customer avatar
by
Bevan
Fort Collins, CO, USA
on Replacement Parts
0points
0out of 0found this question helpful.
Answer this question
1 answer
Answers
answer 1
Hi Bevan, Thank you for your question. If your single handle turns counter-clockwise to turn the faucet on, clockwise to turn off and does not pivot it is most likely a 1300/1400 series faucet. You can switch the trim on your existing faucet out to a new 13/14 series trim using your existing rough in valve. The new trim will come with a RP46074 cartridge. The new cartridge will not work in your existing valve. You will have to continue to use your old cartridge or purchase a new RP19804.
Thanks,
Dave
Skill Level: Advanced
answered 2 months, 3 weeks ago
Customer avatar
by
DeltaFaucet2
0points
0out of 0found this answer helpful.
Question

will part #RP48717 handle fit on my 1300/ 1400 handle as a replacement

asked 3 months ago
Customer avatar
by
paul
on Replacement Parts
0points
0out of 0found this question helpful.
Answer this question
1 answer
Answers
answer 1
Hi Paul, Thank you for your question. The RP48717 handle will work on your 1300/1400 faucet as a replacement.
Thanks,
Dave
Skill Level: Advanced
answered 3 months ago
Customer avatar
by
DeltaFaucet2
0points
0out of 0found this answer helpful.
Question

Delta 1600 Pressure Balanced Valve

We have the 1600 Pressure Balanced Valve in our hotel rooms. Is this valve still available for sale? We need to replace the whole valve.

If it's not available, what would be the replacement valve for it?
Age: 35 to 44
Gender: Male
Project Type: Replacement
Ownership: 10+ years
Skill Level: Intermediate
Topics: Purchase
asked 3 months, 1 week ago
Customer avatar
by
Neal
Canton, OH, USA
on Replacement Parts
0points
0out of 0found this question helpful.
Answer this question
1 answer
Answers
answer 1
Hi Neal, Thank you for your question. The 1600 series faucets have been discontinued since 1994. The replacement stem unit assembly the RP1991, and the RP4993 seats and springs to repair the faucet are still available. The valve body itself is no longer available. The R10000 is our new multichoice rough but it is not compatible with the 1600 series trim.
Thanks,
Dave
Skill Level: Advanced
answered 3 months ago
Customer avatar
by
DeltaFaucet2
0points
0out of 0found this answer helpful.
Question

Tub Only Alternatives

The collection that I have chosen does not include a tub only trim kit, however I have found that Home Depot has the valve only trim kit and a non-divertor spout. Will purchasing these items work with my tub only configuration or must I choose a collection that has a tub only kit?
Age: 45 to 54
Gender: Female
Topics: upgrade
asked 3 months, 1 week ago
Customer avatar
by
Michelle
Arizona, USA
on Replacement Parts
0points
0out of 0found this question helpful.
Answer this question
1 answer
Answers
answer 1
Hi Michelle, Thank you for your question. Combining a valve only trim and a non diverter tub spout will result in a tub only configuration. You will also need a R10000 rough in valve for a complete faucet.
Thanks,
Dave
Skill Level: Advanced
answered 3 months, 1 week ago
Customer avatar
by
DeltaFaucet2
0points
0out of 0found this answer helpful.
Question

Will a Roman Tub faucet model BT2710 fit a spout with an anti- swivel pin underneath?

If there is an anti- swivel pin underneath my Roman Tub spout, will the model #BT2710 fit as well as the T2710? Is there any difference besides looks between the two models? What does the "B" stand for? I only want to change my trim installed in 1993. And if there is no anti-swivel pin will any trim fit, including the BT2710? Also, does it matter where the set screw is on my tub deck? I have attached pictures.
Age: 55 to 64
Gender: Female
Topics: replacement parts
User submitted photo
User submitted photo
User submitted photo
asked 3 months, 1 week ago
Customer avatar
by
Andrea
on Replacement Parts
0points
0out of 0found this question helpful.
Answer this question
1 answer
Answers
answer 1
Hi Andrea, Thank you for your question. If your roman tub spout has the anti-swivel pin the spout from the BT2710 is the largest base spout available through Delta, a portion of the anti-swivel pin hole may be exposed when using this spout. If your spout does not have the anti-swivel pin then based on your photos the new trims will work with your existing rough in valve.
Thanks,
Dave
Skill Level: Advanced
answered 3 months, 1 week ago
Customer avatar
by
DeltaFaucet2
0points
0out of 0found this answer helpful.
Question

Will any Delta trim fit my Roman Tub with Delta valves installed in 1993?

I have a Roman Tub with Delta trim, valves, and parts installed in 1993 when the house was built. Can just the trim be replaced with the Addison Trim (T2792)? I would have to remove tile on the front side of the tub to replace the rough(valve) and I don't want to do that. Do I also need to buy a cartridge?
Topics: replacement parts
asked 3 months, 1 week ago
Customer avatar
by
Andrea
on Replacement Parts
0points
0out of 0found this question helpful.
Answer this question
1 answer
Answers
answer 1
Hi Andrea, Thank you for your question, In most cases if the set screw that holds the roman tub spout onto the valve is on the back of the spout you can replace the trim only with a newer version like the T2792 using your existing rough in. If the set screw is on the front of the spout or if the spout has no set screw at all the rough in valve will need to be replaced as well.
Thanks,
Dave
Skill Level: Advanced
answered 3 months, 1 week ago
Customer avatar
by
DeltaFaucet2
0points
0out of 0found this answer helpful.
Question

What trim kits work with 13 Series fixtures?

I am wanting to upgrade our fixtures. I believe what the builder used in our 2003 home is the Classic Monitor 13 Series but I have uploaded pictures to verify. I am only want to replace the trim for the fixtures, not have to put in new valves, cut holes in the walls, etc. What collections will I be able to achieve this?
Age: 45 to 54
Gender: Female
Topics: upgrade options
User submitted photo
User submitted photo
User submitted photo
User submitted photo
asked 3 months, 1 week ago
Customer avatar
by
Michelle
Arizona, USA
on Replacement Parts
0points
0out of 0found this question helpful.
Answer this question
1 answer
Answers
answer 1
Hi Michelle, Thank you for your question. Any of our current trim models that start with T13 or T14 will work with your existing rough ins from 2003. All of our collections will have faucets available in the T13/14 trims, although not all offer a tub only version. The new trims will come with a new cartridge. The new cartridge will not work in your existing rough. You will have to continue to use your existing cartridge or order a new RP19804.
Thanks,
Dave
Skill Level: Advanced
answered 3 months, 1 week ago
Customer avatar
by
DeltaFaucet2
0points
0out of 0found this answer helpful.
Question

Is gap between handle and neck OK?

My handyman replaced an existing Delta plastic handle with a chrome one (RP48717). This is the only one Home Depot carried. There is a gap between where the new handle ends and the plastic one used to end. See pictures. He said this is OK. Will this opening harm anything? Is there a better replacement handle?
Topics: replacement
User submitted photo
User submitted photo
asked 3 months, 2 weeks ago
Customer avatar
by
CEN_MN
on Replacement Parts
0points
0out of 0found this question helpful.
Answer this question
1 answer
Answers
answer 1
Hi Caryn,
Thank you for your question. The gap will not be an issue. You may be able to slide the trim sleeve out further to cover the gap, but not if it pulls the sleeve from the escutcheon.
Thanks,
Dave
Skill Level: Advanced
answered 3 months, 2 weeks ago
Customer avatar
by
DeltaFaucet2
0points
0out of 0found this answer helpful.
Question

Upgrading an old 1600 series without replacing the pipes

I have been told that I have an old 1600 series. Please see attached pictures. Unfortunately we did not know that we would need to replace the diverter and everything else to upgrade the handles and faucet. At this point, do we have any options to upgrade to a brush nickel set without having to tear out all of the new tile we just layed? If so, can you provide me with some options as to what we can buy that will work with the existing plumbing? I am not a plumber and just an amateur so the more instructions or information you can provide the better. Thanks!
Topics: Care/Maintenance, Assembly
User submitted photo
User submitted photo
User submitted photo
asked 3 months, 3 weeks ago
Customer avatar
by
Rob
on Replacement Parts
+1point
1out of 1found this question helpful.
Answer this question
1 answer
Answers
answer 1
Hi Rob, Thank you for your question. The options for updating the 1600 series is limited to the chrome finish only. If you want to go with a brushed nickel finish you will have to change the entire faucet, including the rough in behind the wall. The trim pieces for the 1600 series can be ordered as individual pieces in the chrome finish but no remodel kit is available. Part numbers include the RP6083 Escutcheon, RP6081 Trim sleeve, H71 handle, RP19895 tub spout with pull up diverter, RP28599 shower head, and the RP31544 shower arm and flange. If you want to replace the inner workings of the valve the RP1991 stem assembly and RP4993 seats and springs are also available.
Thanks,
Dave
Skill Level: Advanced
answered 3 months, 3 weeks ago
Customer avatar
by
DeltaFaucet2
+2points
2out of 2found this answer helpful.
Question

I am looking for replacement cartridges for a two handle lav faucet.

I am looking roe replacement cartridges for a two handle lav faucet. This is a "looks a lot like a Delta and Delta parts work just fine but it is not a Delta" (It is in a Manufactured home and those often have Delta look a like faucets.) I need cartridges with metal (brass) stems because the handles use a set screw rather then a through screw.

Yes I am aware of the irony of asking Delta for help with a non-Delta faucet.
Age: 55 to 64
Gender: Male
Skill Level: Advanced
Topics: Care/Maintenance
asked 3 months, 4 weeks ago
Customer avatar
by
Olin L Zuercher
Elkhart, IN, USA
on Replacement Parts
0points
0out of 0found this question helpful.
Answer this question
1 answer
Answers
answer 1
Hi Olin, Thank you for your question. The RP24096 is our 2 handle cartridge with the brass stem. If you are using a lever style handle with a 1/4 turn range of motion you will want to use RP25513 cartridge which also has the brass stem.
Thanks,
Dave
Skill Level: Advanced
answered 3 months, 3 weeks ago
Customer avatar
by
DeltaFaucet2
0points
0out of 0found this answer helpful.
1 2 3 4 5 next>>